SERDOLIT离子交换树脂 聚苯乙烯树脂
产品简介
SERDOLIT离子交换树脂(聚苯乙烯树脂)产品展台为您精选SERDOLIT离子交换树脂(聚苯乙烯树脂)产品,欢迎您来电咨询SERDOLIT离子交换树脂(聚苯乙烯树脂)产品的详细信息!SERDOLIT是一种聚苯乙烯树脂,主要用于分离分子量不高于3 KDa的小分子。其中的不溶性的球形或者不规则多孔体带有阴性或者阳性基团形成阳离子或者阴离子交换树脂。这些带电粒子具有良好的化学、机械以及热稳定性。
产品详细信息
SERDOLIT离子交换树脂
SERDOLIT是一种聚苯乙烯树脂,主要用于分离分子量不高于3 KDa的小分子。其中的不溶性的球形或者不规则多孔体带有阴性或者阳性基团形成阳离子或者阴离子交换树脂。这些带电粒子具有良好的化学、机械以及热稳定性。
孔径
在合成的过程中,聚苯乙烯链与双功能或者多功能试剂交联,大多数情况下是二乙烯基苯(DVB)。较高比例的交联剂意味着更小的孔径(胶型树脂,孔径2-5 nm),因此具有更高的化学和机械稳定性以及更低的水含量。而单位体积中也具有更多的离子化基团,具有更大的交换能力。如果DVB的含量超过20%,聚合物将变得不均一,会产生大孔径。在生产过程中,更大的孔径会变成曲折结构,*终导致巨大孔径。所谓的巨大孔径树脂指的是孔径20-50nm。
Table 1: Relation between cross linkage, water content and exclusion limits.
Cross
Linkage |
Moisture
Content |
ExclusionLimit
|
Resin Type
|
2 %
|
80 %
|
3000 dalton
|
Gel Type
|
4 %
|
70 %
|
1500 dalton
|
|
8 %
|
55 %
|
1000 dalton
|
|
12 %
|
45 %
|
700 dalton
|
|
16 %
|
40 %
|
600 dalton
|
|
20 %
|
50-65 %
|
12000 dalton
|
Macroporous
|
水含量
离子交换树脂是高度吸湿的,只有长时间加热才会丢失所有的水分。如果需要干燥树脂的话,阴离子树脂必须转变成氯形式,阳离子树脂必须转变成钠形式,然后可以在真空中分别加热到60或120度。如果离子交换树脂需要在自由基或者氢形式下无水使用,*好用干燥的有机溶剂洗涤(如丙酮、乙醇、DMF、DMSO等)。干燥树脂的孔径结构变得不能渗透,因此无水反应*好使用巨大孔径树脂。
再生
根据交换能力,离子交换树脂只能吸附一定数量的离子,因此必须进行再生。也就是除掉吸附的离子,大多数情况下通过羟基(阴离子树脂)或氢离子(阳离子树脂)。
应用:
蛋白脱盐
稀释的蛋白溶液不能直接与自由基或者氢形式的树脂接触,因为总是存在非特异吸附、沉淀甚至变性。透析是一个不错的选择:将蛋白溶液装入透析待中,悬浮于10%的树脂悬浮液,并加入指示剂(如SERDOLIT MB, 45500),缓慢搅动树脂。
去除SDS
未结合的变性剂可以用上述的方法去除。
去除SERVALYT两性电解质
在树脂中透析是一种很有效的温和方法。(推荐使用VISKING透析袋)
纯化甲酰胺,清洁丙烯酰胺和尿素溶液
水处理
精炼糖
制备和纯化药品(***、维生素、生物碱、氨基酸、多肽等)
催化作用
Table 2: Conditioning of Ion Exchangers
The experimental procedures given in the table below should be applied for quantitatively transferring an ion exchange resin from one ionic status into another. An excess of reagents is applied at the laboratory scale, economical considerations are of minor importance as compared to completeness of the reactions.
The experimental procedures given in the table below should be applied for quantitatively transferring an ion exchange resin from one ionic status into another. An excess of reagents is applied at the laboratory scale, economical considerations are of minor importance as compared to completeness of the reactions.
Ion Exchanger
|
Reaction
|
Reagent
|
Reagent/
Resin Volumes |
Flow Rate
cm/min1, 2) |
Rinse Water/
Resin Volumes |
Rinse until
|
Strongly acidic
sulfonic acid cation exchanger |
Na+ --> H+ --> ("Regeneration")
H+ --> Na+ Ca++ --> Na+ |
2N HCl
1N NaCl, 1 N NaOH 2N NaCl |
5
5 5 |
2
2 2 |
6
6 |
pH >5 neutral
Cl negative Cl negative |
Weakly acidic
carboxylic acid cation exchanger |
Ca++ --> H+ ("Regeneration")
Ca++ --> Na+ ("Regeneration") H+ --> Na+ |
0.5N HCl
1N NaCl 2N NaOH |
4
10 8 |
1
1 1 |
15
15 15 |
pH > 5
Cl negative pH< 8 |
Weakly basic
tertiary amine anion exchanger |
Cl --> free amine
free amine --> Cl |
1N Na2CO3, 1N NH4OH
1N HCl |
8
3 |
1
1 |
10
4 |
pH < 8
pH > 6 |
Strongly basic
quart. amine type I |
Cl --> OH ("Regeneration")
HCO3 --> OH OH --> formate Cl --> formate |
2N NaOH
2N NaOH 2N formic acid same as OH-form |
8
4 5 |
2
2 2 |
8
8 8 |
pH < 9
pH < 9 pH > 5, E280(0.013) |
Strongly basic
quart. amine type II |
Cl --> OH
Cl --> NO2- |
2N NaOH
1N NaNO2 |
5
4 |
2
2 |
10
6 |
pH < 9
Na-flame negative |
Chelating resin
|
Cu++ --> H+
Na+ --> NH4+ |
1N HCl
2N NH4OH |
4
4 |
1
2 |
6
6 |
pH > 5
|
2) Volume flow rate in ml/minute is obtained by multiplying the flow rate with the cross section of the column in cm2.
3) If E260 = 0.01 is not attainable, wash with 50 - 100 volume acid at max. 0.1 cm/minute.