**销售日本YUKEN电磁换向阀

**销售日本YUKEN电磁换向阀
上海乾拓贸易有限公司
企业QQ：
电话；
手机；（微信）
邮箱；@163.com
地址：上海市嘉定区江桥嘉涌路99弄6号楼713室
此外，使用湿式电枢螺线管，阀门可确保使用寿命长。
These DSG-005 series solenoid operated directional valves are the pro- ducts newly developed as a "Mini-series".
 Compared with DSG-01 series, t he valves are much more compactly manufactured but enjoy a maximum operating pressure of 25 MPa (3630 PSI)
 and a maximum flow rate of 10 L/min (2.6 U.S.GPM),
油箱端口不要将油箱端口连接到其中具有浪涌压力的任何管道。
Always be sure to use hydraulic fluids within the stipulated conditions shown below:
子板可用。从上表中**子板型号。
Mounting Posture For any model, there are no restrictions regarding the mounting posture.
请注意浪涌电压。安装姿势对于任何型号，安装姿势没有任何限制。
 Please maintain the degree of contamination within NAS 1638-Grade 1 1.  Use 20 µm or finer line filter. Control of Contamination
Solenoids Instructions As the solenoids have no surge absorbers, please pay cautious attention to a surge voltage.
安装螺栓包括表中的四个内六角头螺钉。
与DSG-01系列相比，阀门制造更加紧凑，
但工作压力为25 MPa（3630 PSI），
流量为10 L / min（2.6 USGPM），
同时进一步提升了空间 节省要求。
螺线管通电当给一个螺线管通电时，请务必先预先关闭另一个螺线管。
 Tank Port Do not connect the tank port to any pipe line having a surge pressure in it.
 Be sure to keep the end of the tank line p ipe below the oil level.  As the solenoids are of wet type structure,
it is necessary to make piping in such condition that the inside of the valve is always filled with the fluid.
2粘度：20-200 mm / s（100-930 SSU），
温度：-15至+ 60°C（5至140°F）。**的粘度和油温
必须注意保持对液压油污染的控制，
否则可能会导致液压油的损坏，并缩短阀门的使用寿命。
请保持NAS 1638-Grade 1中的污染程度
Sub-plates are available. Specify the sub-plate model number from the table above. 
When sub-plates are not used, the mounting surface should have a good machined finish.
1.使用20μm或更细的线路滤波器。控制污染
螺线管说明由于螺线管没有浪涌吸收器，
 while contributing further to a space saving requirement. 
Moreover, using wet armature solenoids, the valves ensure the long life.
电磁式方向阀DSG-005
流体类型液压油可以使用表中列出的任何类型的液压油。
确保将油罐管线的末端保持在油位以下。
由于螺线管是湿式结构，因此必须在阀内部总是充满流体的状态下进行配管。
Solenoid Operated Directional Valves DSG-005
Fluid Types Hydraulic Fluids Any type of hydraulic fluid listed in the table below can be used.
Mounting Bolts Four socket head cap screws in the table below are included.
这些DSG-005系列电磁换向阀是新开发的“迷你系列”产品。
2  Viscosity:  20-200 mm /s (100-930 SSU), Temperature:  -15 to+60°C (5 to 140°F). Recommended Viscosity and Oil Temperatures
Solenoid Energisation When energising one solenoid, be sure to de-energise another solenoid beforehand.
当不使用子板时，安装表面应具有良*的加工精加工。
始终确保在下列规定条件下使用液压油：
Due caution must be paid to maintaining control over contamination of the hydraulic fluids
 which may otherwise lead t o breakdowns and shorten the life of the valve.

**销售日本YUKEN电磁换向阀