热流道专业术语中英对照
入水：gate
进入位： gate location 水口形式：gate type 大水口：edge gate
细水口： pin-point gate 水口大小：gate size
转水口：tching runner/gate 唧嘴口径： sprue diameter
流道: runner
热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate
圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴： hot sprue
热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头： connector plug 插座： connector socket 密封/封料： seal
运水：water line 喉塞：line lpug 喉管：tube
塑胶管：plastic tube
快速接头：jiffy quick connector plug/socker
模具零件： mold components 三板模：3-plate mold 二板模：2-plate mold
边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边l：guide pin
顶针板：ejector retainner plate
托板： support plate 螺丝： screw 管钉：dowel pin
开模槽：ply bar scot
内模管位：core/cavity inter-lock 顶针： ejector pin 筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate
缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert
压座/斜鸡：wedge
耐磨板/油板：wedge wear plate 压条：plate
撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate
定位圈：locating ring 锁扣：latch
扣鸡：parting lock set 推杆：push bar 栓打螺丝：s.h.s.b 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush
垃圾钉：stop pin 隔片：buffle
**柱：spring rod **:die spring
中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin
销子：dowel pin 波子**：ball catch 喉塞: pipe plug 锁模块：lock plate 斜顶：angle x pin
斜顶杆：angle ejector rod 尼龙拉勾：parting locks 活动臂：lever arm
复位键、提前回杆：early return bar 气阀：valves
斜导边：angle pin 术语：terms
承压平面平衡：parting surface support balance 模排气：parting line venting
回针碰料位：return pin and cavity interference 模总高超出啤机规格：mold base shut hight 顶针碰运水：water line interferes withejector pin 料位出上/下模：part x cavith (core) side
模胚原身出料位：cavity direct cut on a-plate,core direct cut on b-plate. 不准用镶件： do not use (core/cavity) insert 用铍铜做镶件： use beryllium copper insert
初步（正式）模图设计：preliinary (final) mold design 反呵：reverse core
**压缩量：spring compressed length 稳定性好：good stability,stable 强度不够：insufficient rigidity 均匀冷却：even cooling 扣模：sticking
热膨胀：thero expansion 公差：tolorance 铜公(电极）：copper electrode 模
注塑模部分中英文对照
塑料成形模具mould for plastics 热塑性塑料模mould for thermoplastics 热固性塑料模mould for
thermosets
压缩模compression mould 压注模、传递模transfer
mould 注射模injection mould
热塑性塑料注射模 injection mould for thermoplastics 热固性塑料注射模 injection mould for thermoses
成形零件 定模stationary mould fixed half 动模movable mould moving half
定模座板fixed clamp plate, top clamping plate. top plate 动模座板moving clamp plate. bottom clamping plate. bottom plate 上模座板upper clamping plate 下模座板 lower clamping
plate 凹模固定板 cavity-retainer plate
型芯固定板core-retainer plate 凸模固定板punch-retainer plate 模套 chase. bolster.
frame
支承板backing plate. supprr plate 垫块 spacer parallel
支架ejector housing. mould base
leg 动模movable mould
moving
half 定模座板 fixed clamp plate, top clamping plate. top plate
动模座moving clamp plate. bottom clamping plate. bottom
plate 上模座板upper clamping
plate 下模座板 lower clamping plate
凹模固定板cavity-retainer
plate 型芯固定板core-retainer
plate 凸模固定板punch-retainer plate 模套chase. bolster. Frame 垫块spacer
parallel 支架ejector housing. mould base
leg 压力铸造模具 die-casting die
压铸模零部件
定模fixed die, cover
die 定模座板fixed clamping
plate 定模套板 bolstor, fixed
die 动模moving die,ejector die
动模座板moving clamping
pla 直流道sprue 横流道runner 内浇口 gate
