汞泄漏防护产品

460005                                  520270                            523250

汞泄漏防护套装使用说明

1.Evacuate employees from the spill area.

疏散泄漏区域的员工。

2.Personal protective equipment for exposure to mercury should be worn.

暴露在水银下时应戴上个人防护装备

3.Ventilate the contaminated area.

将污染的区域进行通风

4.Shake the vapor suppressor over the contaminated area being sure to cover any visible mercury。

在污染区域摇晃蒸汽抑制剂，确保覆盖所有可见的水银。

5.Collect all vapor suppressor covered mercury using the wooden spatula and the mercury aspirator bottle. Wait 30 minutes before final clean-up.

用木抹刀和吸汞瓶收集所有覆盖在水银上的蒸汽抑制剂。等待30分钟后清理。

6.Empty the aspirator bottle into the mercury waste bottle.

将吸气瓶倒入废汞瓶中。

7.Activate the MERCSORB® Amalgamation Powder with two (2) ounces powder in a plastic mixing cup. Apply just enough water to form a paste (about 1 ounce). Mix the MERCSORB® Powder and water with a wooden spatula. 。

将MERCSORB®混汞粉与两盎司的粉末放在塑料搅拌杯中进行混合。用适量的水搅拌成糊状(约1盎司)。用木铲将MERCSORB®粉和水混合。

8. Apply a strip of MERCSORB paste across the edge of the mercury-contaminated area.Push the strip slowly across the contaminated surface with a wooden spatula. Apply the MERCSORB® paste in one direction only. Small droplets of mercury will be absorbed in the MERCSORB® paste.

在汞污染区域的边缘涂上一条MERCSORB膏。用木抹刀缓慢地推动带钢穿过污染表面。只向一个方向涂抹MERCSORB®膏体。小滴汞将被吸收在MERCSORB®膏体。

9.  Apply a second strip of the MERCSORB® past to the area and push the strip across the area a second time.

将MERCSORB®经过的**条带应用于该区域，并将该条带再次推过该区域。

10.  Place the contaminated MERCSORB® paste into a sealed plastic container.

将污染的MERCSORB®膏体放入密封的塑料容器中。

11.  Scrub the contaminated area using a moist sponge and warm soapy water.

用湿海绵和温肥皂水擦洗污染区域。

12. Dispose of the used items and products in accordance with all local, state and federal regulations.

 按照所有地方、州和联邦的规定处理使用过的物品和产品规定。

13. After all visible mercury has been properly collected from horizontal surface; sprinkle Mercury Indicator Powder over contaminated area. For vertical surfaces, mix one (1) part Mercury Indicator Powder with four (4) parts water to form a slurry. Paint the slurry on the contaminated vertical surface.

把所有能看得到的水平面上的水银收集之后，再在污染区域撒上水银指示粉。对于垂直表面，将一份水银指示粉与四份水混合成泥浆。将浆液涂在污染的垂直表面。

14. Mercury Indicator Powder should be left undisturbed on the contaminated surface for 24 hours.

水银指示粉应在污染表面静置24个小时。

15. A color change of pink to reddish-brown spots indicates contamination. Large black spots or areas indicate fresh or extensive mercury contamination

粉红色到红棕色斑点的颜色变化表明污染。大黑点或区域表明有新的或广泛的汞污染。

16.Collect the Mercury Indicator Powder and place in a temporary disposal bag.

收集水银指示粉，放入临时弃置袋内。

17. Clean up remaining mercury contaminated area with physical and chemical means.

用物理和化学方法**残留的汞污染区域。

18. Repeat steps 12-16 until no indication of mercury is observed.

重复步骤12-16，直到没有观察到汞的迹象。

19. All used products are contaminated and must be disposed of as toxic waste in accordance with local, state and federal regulations.

所有使用过的产品都受到污染，必须按照当地、州和联邦法规作为有毒废物进行处理。

Note: Depending on the size and extent of the spill, additional equipment may be needed. Kit sorbency capacity is 25ml (337g) of Mercury. CAUTION: Only trained personnel should respond to mercury spills. MERCSORB® kits do not contain any chemicals designed to alter the mercury’s oxicity or danger. Mercury is absorbed directly through the skin and inhalation. Kit is designed for one-time use only.

注:根据泄漏的规模和程度，可能需要额外的设备。试剂盒吸附能力为25毫升(337克)汞。注意:只有训练有素的人才能应对水银泄漏。MERCSORB®试剂盒不包含任何旨在改变汞的氧化性或危险性的化学物质。汞是通过皮肤直接吸收和吸入的。工具包只设计一次使用。

产品留言

标题

联系人

联系电话

内容

验证码

点击换一张

注：1.可以使用快捷键Alt+S或Ctrl+Enter发送信息!
2.如有必要,请您留下您的详细联系方式!