产品名称：REXROTH力士乐电磁换向阀

1)电磁换向阀的轴线必须按水平方向安装，如垂直方向安装，受阀芯、衔铁等零件重量影响，将造成换向或复位不正常。
2)一般电磁阀两端的油腔是泄油腔或回油腔，应检查该腔压力是否过高。如果在系统中多个电磁阀的泄油或回油管道中接

在一起造成背压过高，则应将它们单独接回油箱。
3)安装底板表面应磨削加工，同时应有平面度要求，不得凸起。
4)安装螺钉不能拧得太松，否则板式连接电磁换向阀与底板的接合处渗油。
5)电磁换向阀应注意控制电源参数应与电磁阀一致。电磁换向阀是依靠电磁铁的推力达到换向目的，电磁铁分直流或交流，

电磁铁应与控制电源参数相一致，否则有可能造成换向阀不能正常工作或烧毁电磁铁。

3WE5A-6.0/AW220-50Z4,3WE5B-6.0/AW220-50Z4,3WE5C-6.0/AW220-50Z4

3WE5A-6.0/AG24NZ4,3WE5A-6.0/AW220-50Z5L,3WE5B-6.0/AG24NZ4
3WE5C-6.0/AG24NZ4,3WE5C6.0/AG24Z5L,3WE5B-6.0/AW220-50Z5L,
3WE5C-6.0/AW220-50Z5L,3WE5B6.0/OFAW220RZ5L,3WE5B6.0/AW220RZ5L,
3WE5B6.0/OFAW220RZ5,3WE5B6.0/OFAW22050Z5L,3WE5B6.0/OFAG24Z5L,
3WE5B6.0/AW220-50NZ4,3WE5B6.0/AG24NZ4,3WE5B6.0/AW220RNZ4,
3WE5B6.0/AW220-50NZ5,3WE5B6.0/AG24NZ5,3WE5B6.0/AW220RNZ5,
3WE5B6.0/AW220-50NZ5L,3WE5B6.0/AG24NZ5L,3WE5B6.0/AW220RNZ5L,
3WE5B6.0/AW220-50Z4,3WE5B6.0/AG24Z4,3WE5B6.0/AW220RZ4,
3WE5B6.0/AW220-50Z5, 3WE5B6.0/AG24Z5,3WE5B6.0/AW220RZ5,
3WE5B6.0/AW22050Z5L,3WE5B6.0/AG24Z5L,3WE5B6.0/AW22050Z5L,
3WE5B6.0/AG24Z5L,3WE5C6.0/AW22050Z5L,3WE5B6.0/OAW22050NZ4,
3WE5B6.0/OAG24NZ4,3WE5B6.0/OAW220RNZ4,3WE5B6.0/OAW220-50NZ5,
3WE5B6.0/OAG24NZ5,3WE5B6.0/OFAW220RZ5,3WE5B6.0/OFAW22050Z5L,
3WE5B6.0/OFAG24Z5L,3WE5B6.0/OFAW220RZ5L,3WE5B6.0/AW220RZ5L,
3WE5B6.0/AW220-50NZ4,3WE5B6.0/AG24NZ4,3WE5B6.0/AW220RNZ4,
3WE5B6.0/AW220-50NZ5,3WE5B6.0/AG24NZ5,3WE5B6.0/AW220RNZ5,
3WE5B6.0/AW220-50NZ5L,3WE5B6.0/AG24NZ5L,3WE5B6.0/AW220RNZ5L,
3WE5B6.0/AW220-50Z4,3WE5B6.0/AG24Z4,3WE5B6.0/AW220RZ4,
3WE5B6.0/AW22050Z5,3WE5B6.0/AG24Z5,3WE5B6.0/AW220RZ5,
3WE5C6.0/OAW220-50NZ4,3WE5C6.0/OAG24NZ4,3WE5C6.0/OAW220RNZ4,
3WE5C6.0/OAW220-50NZ5,3WE5C6.0/OAG24NZ5,3WE5C6.0/OAW220RNZ5,
3WE5C6.0/OAW220-50NZ5L,3WE5C6.0/OAG24NZ5L,3WE5C6.0/OAW220RNZ5L,
3WE5C6.0/OAW220-50Z4,3WE5C6.0/OAG24Z4,3WE5C6.0/OAW220RZ4,
3WE5C6.0/OAW220-50Z5,3WE5C6.0/OAG24Z5,3WE5C6.0/OAW220RZ5,